TROY Group Bluetooth Print Adapter Manual de usuario Pagina 1

User’s GuideBluetoothTMPrint AdapterPart Number 40150-100Revision 1.0TM

1-4ing activity. Since you have not made a connection yet, both of these LEDsshould be off.Verifying the Connection to the PrinterBefore attempting t

Configuring the Software on Your PCYou can now configure a laptop PC to print wirelessly to your EPSON printerequipped with an WindConnect Bluetooth P

one of these older cards, first install the software and then upgrade the softwareusing the BluetoothSoftware Suite Upgrade included on the WindConnec

rectly installed the Bluetooth PCMCIA card and software). Click on any oneof these ports and verify that the Serial Port Profile is checked. If it is

3. Right-Click on the printer you wish to associate with the network port, andselect Properties.4. If you are using Windows NT/2000/XP, go to the Port

2-5If you are running Windows 95/98/ME, select Other, highlight Troy GroupTroy Bluetooth Port, and click OK.7. The TROY Bluetooth Port Monitor screen

If you are running Windows 95/98/ME, the Details tab should look some-thing like this:You are now ready to print.Printing the First JobYou should now

2-7This screen will show all of the available WindConnect Bluetooth print adapters.If this is your first print adapter installation, you will only see

2-8DisconnectingYour Bluetooth connection will automatically be disconnected after one minute ofinactivity. You can change this parameter by right cl

Configuring OtherDevices The WindConnect Bluetooth Print Adapter is designed to allow printing from avariety of different Bluetooth devices. Such dev

iiCopyright NoticeAll rights reserved. No part of this publication may be reproduced, stored, in aretrieval system, or transmitted in any form or by

Bluetooth TBT1 port. This procedure is similar to the procedure described inthe Adding a Windows Printer section of the previous chapter except that

3-32. You should see the Discover icon. If you don’t, scroll down by clicking onthe scroll bar arrows on the left side of the screen. Click the Dis

4. Click OK.5. If desired, change the Driver Name to match your printer (the standardGeneric driver will work with most printers, but will not handle

name or the address, depending on the program) and associate the WindConnectBluetooth Print Adapter’s P1 service. You should now be able to print.Usi

1. Turn the phone on by holding down the No key for several seconds.2. Push the right arrow key five times until you see 5 Extras.3. Push the Yes k

4-1Using the Serial Port The WindConnect has an RS-232 serial port that can be used to connect a consoleterminal, a serial printer, or a wide variety

By default the serial port is set in console mode. In this mode, the port settings arepermanently fixed at 115.2Kbps, 8-bit characters, no parity, an

Troubleshooting If You Can’t PrintIf you are unable to print from your laptop or other device to the WindConnectBluetooth Print Adapter, then check th

5-2

Where to Get HelpTROY offers several customer support options to assist you in the event you expe-rience difficulties with your WindConnect, including

ContentsIntroductionWindows System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2About Your User’s Guide . . . . . . .

Returning ProductsIf you need to return a TROY product for any reason (failures, incorrect ship-ments, etc.), first contact TROY at +1 (208) 955-1000

NoticesFCC Compliance StatementFor United States UsersThis equipment has been tested and found to comply within the limits for a ClassB digital device

For European UsersThis product is in conformity with the protection requirements of EU CouncilDirective 89/336/EEC on the approximation of the laws of

REGULATORY INFORMATIONEuropean Union (EU)TROY hereby declares that the Bluetooth™ wireless technology built into theWindConnect Print Adapter, is in

The radiated output power of WindConnect is far below the FCC radio frequen-cy exposure limits. Nevertheless, the WindConnect shall be used in such a

iv

IntroductionThe TROY WindConnectTMBluetoothTMPrint Adapter is a device that enableswireless communications capabilities on most models of printers. B

WindowsTMSystem RequirementsTo use the WindConnect Bluetooth Print Adapter for printing from a PC, yoursystem should include:◗ An IBM-compatible PC wi

1-1Installing the WindConnect Print Adapter HardwareThe WindConnect Bluetooth Print Adapter plugs directly into the parallel port ofthe printer. If d

1-2Before Your BeginBefore you install the WindConnect Bluetooth Print Adapter, make sure that yourprinter and your laptop computer already function p

Connecting to the PrinterBefore connecting the WindConnect Bluetooth Print Adapter, make sure that theprinter is turned off.The WindConnect has a 36-p